Time to beat a dead horse

[FoxRodStang]

I have been looking & looking for an intake tube to replace my stocker. MAF will be replaced with a lightning unit at the same time. I wanted a JLT, but they don't make them for foxes anymore. I'd prefer one that's not metal to help keep heat out of the intake, however, I can't seem to find anything but metal ones for foxes. Any suggestions?

Thanks!

[BadMoFo]

good luck, been looking for months. did you want a complete cai or just the rai from jlt? I wanted just the rai but I know there are a few places that still sell the cai from jlt.

[bonesgt]

This is what I have on my 87GT. You use the factory elbow to the Mas Air.

http://www.moroso.com/catalog/categorydisplay.asp?catcode=34002

http://www.moroso.com/catalog/images/65847_descrip.jpg

[93volpe]

This is what I have on my 87GT. You use the factory elbow to the Mas Air.

http://www.moroso.com/catalog/categorydisplay.asp?catcode=34002

http://www.moroso.com/catalog/images/65847_descrip.jpg


Same here on my 93 LX.... or you could redneck it and go to the harware store...pvc pipe and elbows can be used . exact size and some fitting is required plus they have the rubber reducer to go from one size to the other... neccessity is the mother of invention

[FoxRodStang]

good luck, been looking for months. did you want a complete cai or just the rai from jlt? I wanted just the rai but I know there are a few places that still sell the cai from jlt.

i'm looking for the complete tube...from throttle body to maf, from maf to fenderwell mount filter.

[FoxRodStang]

bones & 93volpe, I've seen that model before, but, its not exactly what I'm looking for...see above post.

[93volpe]

you might wanna try Justine at Palmetto Pony he may be able to come up with something..... 803-532-8181

[FoxRodStang]

thanks man, he's looking around to see what he can come up with.

[BadMoFo]

ok go on ebay and type in jlt and it should bring up a long list of cai kits for them. I want to say texas mustangs or something like that still has the jlt cai that goes into the fender.

[SVTSkip]

Should be easy to home build one, but running into the same issue a short while ago I went with an old school Pro-M setup that I scored with my MAF for a good deal. I needed it with the new 30#ers anyway LOL !

[FoxRodStang]

Should be easy to home build one, but running into the same issue a short while ago I went with an old school Pro-M setup that I scored with my MAF for a good deal. I needed it with the new 30#ers anyway LOL !

any idea where I can find the rubber connectors & elbows?

[XSR]

any idea where I can find the rubber connectors & elbows?


HomeDepot, Lowe's, Ace, etc.....

[FoxRodStang]

HomeDepot, Lowe's, Ace, etc.....

I've found the couplers, but, no elbows that will fit between the throttle body & strut tower.

[SVTSkip]

Just get a piece of pvc for that from Lowe's or something...

[WILDSTANGRACING]

make your own from pvc or you can get silicone elbow from ebay i have some for 3" tubing straits 90 just let me know if i can help

[crumbie]

or just run the factory airbox and factory intake tubes/pipes with a panel filter, aftermarket mass air, and aftermarket throttlebody.

[SVTSkip]

A LOT of folks do just that !

[FoxRodStang]

make your own from pvc or you can get silicone elbow from ebay i have some for 3" tubing straits 90 just let me know if i can help

do you have an elbow that will fit near the throttle body? Thats what I've been looking for.